Skip to the content of the web site.

Rather than spending time going through my publications, you can gain some quick idea on my research since joining Waterloo in 11/2008 from my talk given in 2014; and my research during 2003-2008 at National Research Council from my talk given in 2008.

Here is my PhD oral examination that summarized my research during 1998-2003 at Princeton.

Journal articles:

2014

  1. Zhang J, Irannejad M, Yavuz M and Cui B, “Enhanced sensitivity of smooth gold nanohole array by thermal annealing”, J. Phys. Chem. C, revised manuscript submitted.
  2. Zhang J, Irannejad M and Cui B, “Fabrication of bow-tie structure with ultra-narrow gap for surface enhanced Raman spectroscopy (SERS)”, Plasmonics, in press.
  3. Sun X, Radovanovic PV, and Cui B, “Advances in spinel Li4Ti5O12 anode materials for lithium-ion batteries”, New Journal of Chemistry, appeared online. (review article, 27 pages).
  4. Abbas AS, Alqarni S, Shokouhi BB, Yavuz M, and Cui B, “Water soluble and metal-containing electron beam resist poly(sodium 4-styrenesulfonate)”, Mater. Res. Express,1, 045102 (2014). PDF
  5. Zhang J, Con C and Cui B, “Electron beam lithography on irregular surfaces with evaporated resist”, ACS Nano, 8, 3483–3489 (2014). PDF
  6. Saffih F, Con C, Alshammari A, Yavuz M, and Cui B, “Fabrication of silicon nanostructures with large taper angle by reactive ion etching”, J. Vac. Sci. Technol. B, 32, 06FI04 (2014). PDF
  7. Dey RK and Cui B, “Lift-off with solvent for negative resist using low energy electron beam exposure”, J. Vac. Sci. Technol. B, 32, 06F507 (2014). PDF
  8. Wan W, Lin L, Xu Y, Guo X, Liu X, Ge H, Lu M, Cui B, and Chen Y, “Planar self-aligned imprint lithography for coplanar plasmonic nanostructures fabrication”, Applied Physics A, 116, 657–662 (2014). PDF
  9. Dey RK and Cui B, “Electron beam lithography with in-situ feedback using self-developing resist”, Nanoscale Research Letters, 9, 184 (2014). PDF
  10. Irannejad M, Zhang J, Yavuz M and Cui B, “Numerical study of optical behavior of nano-hole array with non-vertical sidewall profile”, Plasmonics, 9, 537–544 (2014). PDF
  11. Con C, Zhang J and Cui B, “Nanofabrication of high aspect ratio structures using evaporated resist containing metal”, Nanotechnology, 25, 175301 (2014). PDF
  12. Alhazmi M, Aydinoglu F, Cui B, Ramahi OM, Irannejad M, Brzezinski A, and Yavuz M, “Comparison of the Effects of Varying of Metal Electrode in Metal-insulator-metal Diodes with Multi-Dielectric Layers”, Austin Journal of Nanomedicine & Nanotechnology, 2(2), 4 (2014). PDF
  13. Aydinoglu F, Alhazmi M, Cui B, Ramahi OM, Irannejad M, Brzezinski A, and Yavuz M, “Higher Performance Metal-Insulator-Metal Diodes using Multiple Insulator Layers”, Austin Journal of Nanomedicine & Nanotechnology, 1(1), 3 (2014). PDF
  14. Sun X, Hegde M, Wang J, Zhang Y, Liao JY, Radovanovic PV, and Cui B, “Structural Analysis and Electrochemical Studies of Carbon Coated Li4Ti5O12 Particles Used as Anode for Lithium Ion Battery”, ECS Transactions, 58, 79-88 (2014). PDF
  15. Sun X, Wang YQ, Hegde M, Shu J, Bai XD, Zhang YF, Radovanovic PV, and Cui B “Structure and Electrochemical Properties of Spinel Li4Ti5O12 Nanocomposites as Anode for  Lithium-Ion Battery”, International Journal Electrochemical Science, 9, 1583-1596 (2014). PDF
  16. Abbas AS, Yavuz M and Cui B, “Polycarbonate electron beam resist using solvent developer”, Microelectron. Eng., 113, 140-142 (2014). PDF
  17. Bai X, Wen D, Con C, Zhang J, Yavuz M and Cui B, “Research on Fabrication and Electronic Characteristics of Dual-Extended Nano Structure Memristor”, Key Engineering Materials, 609-610, 728-733 (2014).

2013

  1. Dey RK and Cui B, “Stitching error reduction in electron beam lithography with in-situ feedback using self-developing resist”, J. Vac. Sci. Technol. B, 31 (6), 06F409 (2013). PDF
  2. Irannejad M, Yavuz M and Cui B, “Finite difference time domain study of light transmission through multihole nanostructures in metallic film”, Photonics Research, 1(4), 154-159 (2013). PDF
  3. Sun X, Sun K, Wang Y, Bai X and Cui B, “Scale-up synthesis, structure characterization and electrochemical characteristics of C-LiFePO4 nanocomposites for lithium ion rechargeable batteries”, Int. J. Electrochem. Sci., 8, 12816-12836 (2013). PDF
  4. Con C, Abbas AS, Yavuz M and Cui B, “Dry Thermal Development of Negative Electron Beam Resist Polystyrene”, Advances in Nano Research, 1, 105-109 (2013). PDF
  5. Con C and Cui B, “Effect of mold treatment by solvent on PDMS molding into nanoholes”, Nanoscale Research Letters, 8, 394 (2013). PDF
  6. Irannejad M and Cui B, “Effects of refractive index variations on the optical transmittance spectral properties of the nano-hole arrays”, Plasmonics, 8, 1245-1251 (2013). PDF
  7. Chen JY, Con C, Yu MH, Cui B and Sun KW, “Efficiency enhancement of PEDOT:PSS/Si hybrid solar cells by using nanostructured radial junction and antireflective surface”, ACS Appl. Mater. Interfaces, 5 (15), 7552–7558 (2013). PDF
  8. Liu R, Zhang F, Con C, Cui B and Sun B, “Lithography-free fabrication of silicon nanowire and nanohole arrays by metal-assisted chemical etching”, Nanoscale Research Letters, 8, 155 (2013). PDF
  9. Dey RK, Mansour R and Cui B, “Effect of molecular weight distribution on e-beam exposure properties of polystyrene”, Nanotechnology, 24, 245302 (2013). PDF

2012

  1. Sun X, Sun K, Chen C, Sun H and Cui B, “Controlled Preparation and Surface Structure Characterization of Carbon-Coated Lithium Iron Phosphate and Electrochemical Studies as Cathode Materials for Lithium Ion Battery”, International Journal of Materials and Chemistry, 2(5), 218-224 (2012). PDF
  2. Zhang J, Shokouhi B and Cui B, “Tilted nanostructure fabrication by electron beam lithography”, J. Vac. Sci. Technol. B, 30(6), 06F302(2012). PDF
  3. Liu W, Ferguson M, Yavuz M and Cui B, “Porous TEM windows fabrication using CsCl self-assembly”, J. Vac. Sci. Technol. B, 30(6), 06F201(2012). PDF
  4. Xuan Y, Guo X, Cui Y, Yuan C, Ge H, Cui B and Chen Y, “Crack-free controlled wrinkling of a bilayer film with a gradient interface”, Soft Matter, 8, 9603-9609(2012). PDF
  5. Con C, Dey R, Ferguson M, Zhang J, Mansour R, Yavuz M and Cui B, “High molecular weight polystyrene as very sensitive electron beam resist”, Microelectronic Engineering, 98, 254-257(2012). PDF
  6. Con C, Zhang J, Jahed Z, Tsui TY, Yavuz M and Cui B, “Thermal nanoimprint lithography using fluoropolymer mold”, Microelectronic Engineering, 98, 246-249(2012). PDF

2011

  1. Shokouhi B, Zhang J and Cui B, “Very high sensitivity ZEP resist using MEK:MIBK developer”, Micro & Nano Lett. 6(12), 992–994 (2011). PDF
  2. Ma S, Con C, Yavuz M and Cui B, “Polystyrene Negative Resist for High Resolution Electron Beam Lithography”, Nanoscale Research Letters, 6, 446 (2011). PDF
  3. Zhang J, Fouad M, Yavuz M and Cui B, “Charging effect reduction in electron beam lithography with nA beam current”, Microelectronic Engineering, 88(8), 2196-2199 (2011). PDF
  4. Zhang J, Cui B and Ge H, “Fabrication of flexible mold for hybrid nanoimprint-soft lithography”, Microelectronic Engineering, 88(8), 2192-2195 (2011). PDF

2006-2010

  1. Fouad M, Yavuz M and Cui B, “Nanofluidic channels fabricated by e-beam lithography and polymer reflow sealing”, J. Vac. Sci. Technol. B, 28, C6111 (2010). PDF
  2. Cui B, Clime L and Veres T, “Fabrication of nanostar array by nanoimprint lithography”, J. Vac. Sci. Technol. B 28, C6026 (2010). PDF
  3. Rahman SMS and Cui B, “Mold Fabrication for 3D Dual Damascene Imprinting”, Nanoscale Research Letters, 5, 545–549 (2010). PDF
  4. Cui B, Keimel C and Chou SY, “Ultrafast Direct Imprint of Nanostructures in Metals by Pulsed Laser Melting”, Nanotechnol. 21, 045303 (2010). PDF
  5. Malic L, Cui B, Veres T and Tabrizian M, “Nanoimprinted plastic substrates for enhanced surface plasmon resonance imaging detection”, Optics Express, 17(22), 20386-92 (2009). PDF
  6. Geissler M, Li K, Cui B, Clime L and Veres T, “Plastic substrates for surface-enhanced Raman scattering”, J. Phys. Chem. C, 113(40), 17296–17300 (2009). PDF
  7. Li Z, Gu Y, Wang L, Ge H, Wu W, Xia Q, Yuan C, Chen Y, Cui B and Williams RS “Hybrid Nanoimprint−Soft Lithography with Sub-15 nm Resolution”, Nano Lett., 9 (6), 2306–2310 (2009). PDF
  8. Heidi Au HT, Cui B, Chu ZE, Veres T and Radisic M, “Cell culture chips for simultaneous application of topographical and electrical cues enhance phenotype of cardiomyocytes”, Lab Chip, 9, 564–575 (2009). PDF
  9. Guillemette MD, Cui B, Roy E, Gauvin R, Giasson CJ, Esch MB, Carrier P, Deschambeault A, Dumoulin M, Toner M, Germain L, Veres T and Auger FA, “Surface topography induces 3D self-orientation of cells and extracellular matrix resulting in improved tissue function”, Integrated Biology, 1, 196–204 (2009). PDF
  10. Hajiaboli A, Cui B, Kahrizi M and Truong VV, “Optical properties of thick metal nanohole arrays fabricated by electron beam and nanosphere lithography”, Physica Status Solidi A-Applications and Materials Science, 206(5), 976-979 (2009). PDF
  11. Cui B, Wu L and Chou SY, “Fabrication of high aspect ratio metal nano-tips by nanosecond pulse laser melting”, Nanotechnol. 19, 345303 (2008). PDF
  12. Li K, Clime L, Tay L, Cui B, Geissler M and Veres T, “Multiple Surface Plasmon Resonances and Near-Infrared Field Enhancement of Gold Nanowells”, Analytical Chemistry, 80(13), 4945-4950 (2008). PDF
  13. Cui B and Veres T, “High resolution electron beam lithography of PMGI using solvent developer”, Microelectron. Eng. 85, 810-813 (2008). PDF
  14. Cui B, Clime L, Li K and Veres T, “Fabrication of large area nanoprism array and its application for surface enhanced Raman spectroscopy (SERS)”, Nanotechnol. 19, 145302 (2008). PDF
  15. Li K, Clime L, Cui B and Veres T, “Surface Enhanced Raman Scattering on Long-range Ordered Noble-metal Nanocrescent Arrays”, Nanotechnol. 14, 145305 (2008). PDF
  16. Malic L, Cui B, Veres T and Tabrizian M, “Enhanced surface plasmon resonance imaging detection of DNA hybridization on periodic gold nanoposts”, Opt. Lett. 32, 3092 (2007). PDF
  17. Alvarez-Puebla R, Bravo-Vasquez JP, Cui B, Veres T and Fenniri H, “ SERS Classification of Highly Related Performance Enhancers”, ChemMedChem, 2(8), 1165-1167 (2007). PDF
  18. Cui B and Veres T, “Fabrication of metal nanoring array by nanoimprint lithography (NIL) and reactive ion etching”, Microelectron. Eng., 84 , 1544–47 (2007). PDF
  19. Alvarez-Puebla R, Cui B, Bravo-Vasquez JP, Veres T and Fenniri H, “Nanoimprinted SERS-active substrates with tunable surface plasmon resonances”, J. Phys. Chem. C, 111, 6720-23 (2007).  PDF
  20. Cui B, Yu ZN, Ge, HX and Chou SY, “Large area 50 nm period grating by multiple nanoimprint lithography and spatial frequency doubling”, Appl. Phys. Lett., 90, 043118 (2007). PDF
  21. Le Drogoff B, Cui B and Veres T, “Fast 3D Nanostructure Fabrication by Laser-Assisted nano-Transfer Printing”, Appl. Phys. Lett., 89, 113103 (2006). PDF
  22. Cui B and Veres T, “Pattern replication of 100 nm to millimeter-scale features by thermal nanoimprint lithography”, Microelectron. Eng., 83, 902-905 (2006). PDF
  23. Cui B and Veres T, “Polyimide nanostructures fabricated by nanoimprint lithography and its application as flexible imprint mould”, Microelectron. Eng., 83, 906-909 (2006). PDF
  24. Cui B, Wu W, Keimel C and Chou SY, “Filling of Via Holes by Laser-Assisted Direct Imprint (LADI)”, Microelectron. Eng., 83 (4-9), 1547-1550 (2006). PDF

Before 2005

  1. Beauvais J, Lavallee E, Zanzal A, Drouin D, Lau KM, Veres T and Cui B, “Fabrication of a 3D nano-imprint template with a conformal dry vapor deposited electron beam resist”, Proceedings of SPIE, 5751, 392-399 (2005). PDF
  2. Feng J, Cui B, Zhan Y, and Chou SY, “Flexible metal film with micro- and nanopatterns transferred by electrochemical deposition”, Electrochem. Commun., 4, 102-104 (2002). PDF
  3. Kong L, Pan Q, Cui B, Li M, and Chou SY, “Magneto-transport and domain structures in nano-scale NiFe/Cu/Co spin valve”, J. Appl. Phys.  85 (8): 5492-5494 (1999). PDF
  4. Cui B, Wu W, Kong LS, Sun XY, Chou SY, “Perpendicular quantized Magnetic disks with 45 Gbits on a 4x4 cm2 area”, J. Appl. Phys.  85 (8): 5534-5536 (1999). PDF
  5. Chou SY, Kong LS, Wu W, Cui B, “Fabrication, reading and writing of quantized magnetic disks with 65 Gbit/in2 perpendicular storage density and 30 Gbit/in2 longitudinal storage density”, Electrochemical Society Series, 98(20), 253-254 (1999).
  6. Kong L, Zhuang L, Li M, Cui B, Chou SY, “Fabrication, writing, and reading of 10 Gbits/in(2) longitudinal quantized magnetic disks with a switching field over 1000 Oe”, Jpn. J. Appl. Phys. Part 1, 37 (11): 5973-5975 (1998). PDF
  7. Wu W, Cui B, Sun XY, Zhang W, Zhuang L, Kong LS, Chou SY, “Large area high density quantized magnetic disks fabricated using nanoimprint lithography”, J. Vac. Sci. Technol. B 16 (6): 3825-3829 (1998). PDF
  8. Mao W, Yang J, Cui B, Cheng B, Yang Y, Du H, Zhang B, Ye C, and Yang J, “A study on the effect of hydrogen in the compounds with ThMn12-type structure”, J. Phys. - Condensed Matter,10 (12): 2611-2616 (1998). PDF       
  9. Yang J, Cui B, Mao W, Yang Y, Chen D, Yang Y, and Gou C, “A linear muffin-tin orbital calculation of local electronic and magnetic properties of YFe10Mo2 and YFe10Mo2N”, J. Phys. Soc. Jpn., 67 (2): 576-582 (1998). PDF
  10. Yang J, Cui B, Mao W, Cheng B, Yang Y, Ge S, “Hard magnetic properties of NdFe10.5V1.5Nx powders with high performance”, J. Magn. Magn. Mater. 182, 131-136 (1998). PDF
  11. Yang J, Cui B, Mao W, Cheng B, Yang J, Hu B, Yang Y, Ge S, “Effect of interstitial nitrogen on the structural and magnetic properties of NdFe10.5V1.5Nx”, J. Appl. Phys., 83 (5): 2700-2704 (1998). PDF
  12. Yang J, Cui B, Cheng B, Mao W, Yang Y, Ge S, “Preparation of NdFe10.5V1.5Nx powders with potential as high-performance permanent magnets”, J. Phys D: Appl. Phys., 31 (3): 282-286 (1998). PDF
  13. Yang J, Cui B, Mao W, Pei X, Yang Y, “Theoretical calculation on the magnetocrystalline anisotropy of NdFe10.5V1.5Nx”, Solid State Commun., 104 (10): 615-618 (1997). PDF

Book chapter and book edited:

  1. Li K, Morton K, Veres T and Cui B (corresponding author), “Nanoimprint Lithography and its Application in Tissue Engineering and Bio-sensing”, Comprehensive Biotechnology, 2nd edition, Elsevier, 2011. PDF
  2. Cui B (editor), Recent Advances in Nanofabrication Techniques and Applications, Intech, 2011. LINK
  3. Cui B, “Ultrafast Fabrication of Metal Nanostructures Using Pulsed Laser Melting”, chapter in Recent Advances in Nanofabrication Techniques and Applications, Intech, 2011. PDF

Conference presentations and publications:

  1. Dey RK, Cui B, “Lift-off using solvent for negative electron beam resist by ultra-low energy exposure”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  2. Zhang J, Cao K, Wang XS, Cui B, “Metal-containing polymer electron beam resist with high resolution and high etching resistivity”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  3. Saffih F, Alshammari A, Yavuz M, Cui B, “Fabrication of silicon nanostructures with large taper angle by reactive ion etching”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  4. Alshammari A, Con C, Yavuz M, Cui B, “Benchtop fabrication method on non-planar surface using SAM as e-beam resist”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  5. Alshammari A, Yavuz M, Cui B, “Improved anti-adhesion FOTS coating for imprint mold”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  6. Alqarni S, Abbas AS, Yavuz M, Cui B, “Water soluble and developable e-beam resist sodium PSS”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  7. Zhang J, Irannejad M, Yavuz M, Cui B, “Smooth Au Film by Annealing for Enhanced Extraordinary Optical Transmission”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  8. Irannejad M, Zhang J, Yavuz M, Cui B, “Numerical investigation of optical behavior of nano-hole array with non-vertical sidewall profile”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  9. Alqarni S, Abbas AS, Yavuz M, Cui B, “Dry liftoff of metal and organic materials”, 58th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Washington, DC, May 2014.
  10. Xiangcheng Sun, Xuedong Bai, Yongqing Wang, I. D. Hosein, M. Hegde, P. V. Radovanovic, Yu-Guo Guo and Bo Cui, “Comparison of Structural Analysis and Electrochemical Studies of C-Li4Ti5O12 and CNT-Li4Ti5O12 Nanocomposites particles used as Anode for Lithium Ion Battery”, MRS Proceeding, Volume 1541, 2013.
  11. Alshammari A, Yavuz M and Cui B, “Benchtop fabrication method on non-planar surface using SAM as e-beam resist”, 39th International Conference on Micro- and Nano-Engineering (MNE), London, UK, September 2013.
  12. Abbas AS, Yavuz M and Cui B, “Water soluble and developable electron beam resist PSS”, 39th International Conference on Micro- and Nano-Engineering (MNE), London, UK, September 2013.
  13. Abbas AS, Yavuz M and Cui B, “Metal nanostructure fabrication by electron beam lithography and dry liftoff”, 39th International Conference on Micro- and Nano-Engineering (MNE), London, UK, September 2013.
  14. Con C, Alhazmi M, Yavuz M and Cui B, “Freeze-drying for the reduction of e-beam resist collapse”, 39th International Conference on Micro- and Nano-Engineering (MNE), London, UK, September 2013.
  15. Hailu DM, Alqarni S, Cui B and Saeedkia D, “Terahertz Surface Plasmon Resonance Sensor And Bull's Eye Structure For Material Sensing,” The International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz), Mainz, Germany, September 2013.
  16. Hailu D. M., Alqarni S, Cui B and Saeedkia D, “Terahertz surface plasmon resonance sensor for material sensing,” SPIE Photonics North Conference, Ottawa, Canada, June 2013.
  17. Alqarni S, Con C and Cui B, “Out-of-plane nanofabrication using evaporated electron beam resist”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  18. Zhang J, Irannejad M and Cui B, “Fabrication of Gold Bowtie Nano-antenna by E-beam Lithography on Si3N4 Membrane for SERS”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  19. Con C and Cui B, “Nanofabrication of high aspect ratio structures using evaporated polystyrene resist containing metal”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  20. Dey RK and Cui B, “Electron beam optimization using self-developing resist for large write-field electron beam lithography”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  21. Alhazmi M, Yavuz M and Cui B, “Contrast curve engineering by using multi-layer polystyrene electron beam resist”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  22. Irannejad M and Cui B, “Theoretical study of the effects of substrate material refractive index on the optical transmission of nano-hole arrays”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  23. Dey RK and Cui B, “Stitching error reduction in electron beam lithography with in-situ feedback using self-developing resist”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  24. Abbas AS, Yavuz M and Cui B, “Polycarbonate electron beam resist using solvent developer”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  25. Con C and Cui B, “Effect of mold treatment by solvent on PDMS molding into nanoholes”, 57th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Nashville, TN, May 2013.
  26. Zhang J and Cui B, “Nanofabrication on non-flat surface using evaporated electron beam resist polystyrene”, IEEE-NEMS, Suzhou, China, April 2013.
  27. Sun X, Sun K and Cui B, “Surface Structure Characterization and Electrochemical Characteristics of Carbon-Coated Lithium Iron Phosphate (C-LiFePO4) Particles”, MRS Proceedings 1388(1), 2012.
  28. Sun X, Iqbal A, Hosein ID, Yacaman MJ, Tang ZY, Radovanovic PV and Cui B, “Structure Characterization and Electrochemical Characteristics of Carbon Nanotube-Spinel Li4Ti5O12 Nanoparticles”, MRS Proceedings 1440(1), 2012.
  29. (invited) Cui B, “Nanofabrication by nano-imprint and electron beam lithography and applications”, The 12th Emerging Information & Technology Conference, August, Toronto, Canada, August 2012.
  30. Liu W, Ferguson M, Yavuz M and Cui B, “Patterning of porous silicon nitride membrane by CsCl self-assembly”, The 3rd International Conference on Nanotechnology: Fundamentals and Applications, Montreal, Canada, August 2012.
  31. Zhang J, Shokouhi B and Cui B, “Fabrication of tilted nano-pillar and nano-hole arrays by electron beam exposure”,The 3rd International Conference on Nanotechnology: Fundamentals and Applications, Montreal, Canada, August 2012.
  32. Zhang J and Cui B, “Electron beam lithography with evaporated resist”, 56th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Waikoloa, Hawaii, May 2012.
  33. Dey RK, Mansour R and Cui B, “Effect of molecular weight distribution on e-beam resist polystyrene”, 56th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Waikoloa, Hawaii, May 2012.
  34. Liu W, Ferguson M, Yavuz M and Cui B, “Patterning of porous silicon nitride membrane by CsCl self assembly”, 56th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Waikoloa, Hawaii, May 2012.
  35. Con C and Cui B, “Electron beam lithography using dry thermal development”, 56th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Waikoloa, Hawaii, May 2012.
  36. Zhang J, Shokouhi B and Cui B, “Periodic tilted Au structure fabrication by electron beam exposure”, 56th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Waikoloa, Hawaii, May 2012.
  37. (invited) Cui B, “Application of Nanoimprint Lithography in Tissue Engineering and Biosensing”, 5th World Congress of Biotechnology, Xi’an, China, April 2012.
  38. Sun X, Sun K and Cui B, “Structure characterizations of micro-scale LiFePO4/C cathode materials”, 2011 MRS Fall Meeting Proceedings.
  39. (invited) Cui B, “Nanoimprint lithography and its application on tissue engineering and biosensing”, World Congress of Nano-S&T, Dalian, China, October 2011.
  40. Con C, Yavuz M and Cui B, “Thermal nanoimprint lithography using fluoropolymer mold”, 37th International Conference on Micro- and Nano-Engineering, Berlin, Germany, September 2011.
  41. Con C, Zhang J, Ferguson M, Mustafa Yavuz and Bo Cui, “High molecular weight polystyrene as very sensitive electron beam resist”, 37th International Conference on Micro- and Nano-Engineering, Berlin, Germany, September 2011.
  42. Zhang J, Shokouhi B and Bo Cui, “Periodic tilted structure fabrication by electron beam exposure”, 37th International Conference on Micro- and Nano-Engineering, Berlin, Germany, September 2011.
  43. Zhang J, Shokouhi B and Cui B, “High sensitivity electron beam lithography using ZEP resist and MEK:MIBK developer”, 55th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Las Vegas, Nevada, June 2011.
  44. Ma S, Con C, Yavuz M and Cui B, “High Resolution Electron Beam Lithography Using Polystyrene Negative Resist”, 55th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Las Vegas, Nevada, June 2011.
  45. Saffih F, Cui B, Evoy S, Fitzpatrick NN, Mohammad MA, “Bio-inspired Nano-Photodiode for Low Light, High Resolution and Crosstalk-Free CMOS Image Sensing”, IEEE International Symposium on Circuits, ISCAS 2011, Rio de Janeiro, May 2011, pp. 797-800. PDF
  46. Zhang Z and Cui B, “Fabrication of dense periodic 2D nanostructures by electron beam lithography with reduced charging effect”, 36th International Conference on Micro- and Nano-Engineering, Genoa, Italy, September 2010.
  47. Zhang Z and Cui B, “Fabrication of flexible mold for hybrid nanoimprint-soft lithography”, 36th International Conference on Micro- and Nano-Engineering, Genoa, Italy, September 2010.
  48. Fouad M, Yavuz M and Cui B, “Nanofluidic channels fabricated by e-beam lithography and polymer reflow sealing”, 54th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Anchorage, Alaska, June 2010.
  49. Cui B, Clime L and Veres T, “Fabrication of nanostar array by nanoimprint lithography”, 54th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Anchorage, Alaska, June 2010.
  50. Morton K, Cui B, Malic L and Veres T, “Ultrasmooth, 3D Nanostructured Gold Films for Enhanced SPR detection by Nanoimprint Lithography and Template Stripping”, 54th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication (EIPBN), Anchorage, Alaska, June 2010.
  51. Fouad M, Yavuz M and Cui B, “Nanofluidic channels fabricated by e-beam lithography and polymer reflow sealing”, NanoOntario, London, Canada, April, 2010.
  52. Cui B, Clime L and Veres T, “Fabrication of nanostar array by nanoimprint lithography”, NanoOntario, London, Canada, April, 2010.
  53. Rahman SMS and Cui B, “Mold Fabrication for 3D Dual Damascene Imprinting”, Nano and Giga Challenges in Electronics, Photonics and Renewable Energy, Hamilton, Canada, August 2009.
  54. Malic L, Cui B, Veres T and Tabrizian M, “Periodic gold nanopost-based biochips for enhanced surface plasmon resonance imaging detection of DNA hybridization,” NanoQuebec Inno2008, Montreal, Canada, 2008.
  55. Hajiaboli A, Fida F, Cui B, Djaoued Y, Balaji S, Badilescu S, Kahrizi M, Truong VV, “Optical Properties of Thick Metal Nanohole Arrays Fabricated by Electron Beam – and Nanosphere Lithography”, ICOOPMA, Edmonton, Canada, 2008.
  56. Malic L, Cui B, Veres T and Tabrizian M, “Nanostructure enhanced surface plasmon resonance imaging detection of DNA hybridization”, Proceedings of MicroTAS 2007, Paris, France , pp. 442-444, (2007).
  57. Malic L, Cui B, Veres T and Tabrizian M, “Nanostructure and E-field enhanced SPR imaging detection of DNA hybridization,” Colloque Nano 2007, Montreal, Canada (2007).
  58. Li K, Cui B, Clime L, Geissler M and Veres T, “Fabrication of discreet nano arrays by using nanoimprint lithography and their surface-enhanced Raman scattering effect”, MRS fall meeting, Boston, November 2007.
  59. Cui B, Zhao S and Veres T, “High resolution electron beam lithography of PMGI using solvent developer”, Micro- and Nano-Engineering, Copenhagen, September 2007.
  60. Cui B, Li K, Clime L and Veres T, “Fabrication of nanoprisms by nanoimprint lithography”,  Micro- and Nano-Engineering, Copenhagen, September 2007.
  61. Malic L, Tabrizian M, Cui B and Teodor Veres, “Nanostructure and e-field enhanced surface plasmon resonance imaging detection of DNA hybridization”, Colloque NanoQuebec, Montreal, February 2007.
  62. Cui B and Veres T, “Fabrication of metal nanoring array by nanoimprint lithography (NIL) and reactive ion etching”, Micro- and Nano-Engineering, Barcelona, September 2006.
  63. Guillemette MD, Cui B, Deschambeault A, Germain L, Veres T and Auger FA, “Behaviour study of corneal fibroblasts on nanostructured and microstructured polystyrene”, NanoForum, Edmonton, Canada, 2006.
  64. Le Drogoff B, Cui B, and Veres T, “Laser-Assisted nano-Transfer Printing: Application to fast 3D imprint mold fabrication”, Nanoimprint and Nanoimprint Technology (NNT), Kyoto Japan, October 2005.
  65. Cui B and Veres T, “Pattern replication of 100 nm to millimeter-scale features by thermal nanoimprint lithography”, Micro- and Nano-Engineering, Vienna, September 2005.
  66. Cui B and Veres T, “Polyimide nanostructures fabricated by nanoimprint lithography and its application as flexible imprint mould”, Micro- and Nano-Engineering, Vienna, September 2005.
  67. Cui B, Wu W, Keimel C and Chou SY, “Filling of Via Holes by Laser-Assisted Direct Imprint (LADI)”, Micro- and Nano-Engineering, Vienna, September 2005.
  68. Chou SY, Keimel C and Cui B, “Wafer Planarization by Laser Assisted Direct Imprint (PLADI)”, Micro- and Nano-Engineering, Vienna, September 2005.
  69. Cui B, Chiu P, Yang HJ, Veres T, Shih I and Xiao S, “Nano-structured plastic solar cell fabricated by Direct Nanoimprint of Semiconducting Polymer”, Third International Conference on Nanoimprint and Nanoprint Technology, December 2004.
  70. Beauvais J, Mun LK, Drouin D, Lavallee E, Veres T and Cui B, “Three dimensional imprinting template produced using evaporated e-beam resist and reactive ion etching”, Third International Conference on Nanoimprint and Nanoprint Technology, December 2004.
  71. Cui B, Keimel C, Yu Z, Wu W, and Chou SY, “Ultrafast planarization of 200 nm period copper grating by pulsed laser”, Second International Conference on Nanoimprint and Nanoprint Technology, December 2003.
  72. Lei X, Cui B, Ge H, and Chou SY, “Fabrication of subwavelength surface plasmon mirrors by nanoimprint lithography”, Second International Conference on Nanoimprint and Nanoprint Technology, December 2003.
  73. Cui B, Kong L, Wu W, and Chou SY, “Fabrication of magnetic nanostructures, quantized magnetic disks, and spin-valve devices by nanoimprint lithography”, First International Conference on Nanoimprint and Nanoprint Technology, December 2002.
  74. Cui B, Yu Z, Wu W, Ge H, and Chou SY, “Grating frequency doubling using nanoimprint lithography and electroless plating for large area 50 nm period grating fabrication", the 46th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication, June 2002.
  75. Cui B, Kong L, Guo L, and Chou SY, “Spintronics and their fabrication by nanoimprint”, Spins in Semiconductors (SPINS) Workshop, January 2000.
  76. Chou SY, Kong L, Cui B, and Wu W, “Patterned magnetic nanostructure and quantized magnetic disks”, American Physical Society Centennial.
  77. Cui B, Wu W, Sun X, and Chou SY, “Large area quantized magnetic disks (QMDs) fabricated by using nanoimprint lithography and electroplating”, The 43rd Annual Conference on Magnetism and Magnetic Materials, November 1998.
  78. Wu W, Cui B, Sun X, Zhang W, Zhuang L, Kong L, and Chou SY, “High density quantized magnetic disks fabricated using nanoimprint lithography”. the 42th International Conference on Electron, Ion and Photon Beam Technology and Nano-fabrication, June 1998.
  79. Kong L, Pan Q, Li M, Cui B and Stephen Y. Chou, “A new spin-valve magnetic memory cell based on patterned single-domain magnetic multilayer”, The 56th Annual Device Research Conference, June 1998.

Patents:

  1. Chou SY, Cui B and Keimel CF, “Method for filling of nanoscale holes and trenches and for planarizing of a wafer surface”, US Patent 7,510,946 (2009).
  2. Malic L, Veres T, Cui B, Normandin F and Tabrizian M, “System and method for surface plasmon resonance based detection of molecules”, WO Patent 101,348 (2008), US Patent App. 12/527,961 (2008), EP Patent 2,122,333 (2009).
  3. Cui B and Dey RK, “Batch process to make high-aspect-ratio AFM tip”, US Provisional Patent, serial No. 61/854,110.